# Apps disabled to free up system memory

**URL:** <https://community.qnap.com/t/apps-disabled-to-free-up-system-memory/2419>\
**Category:** Firmware\
**Created:** [September 24, 2025, 8:59am UTC](https://community.qnap.com/t/apps-disabled-to-free-up-system-memory/2419 "2025-09-24T08:59:13Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![amnesia](https://avatars.discourse-cdn.com/v4/letter/a/53a042/32.png) [@amnesia](https://community.qnap.com/u/amnesia)\
**Post date:** [September 24, 2025, 8:59am UTC](https://community.qnap.com/t/apps-disabled-to-free-up-system-memory/2419/1 "2025-09-24T08:59:13Z")

</div>

I have a TS-673A with 64GB RAM, running Virtualization Station and Container Station among other applications. Since the last firmware update, I have experienced Virtualization Station and/or Container Station being disabled by the system to free up system memory, even though the system uses below 50% of the RAM.

The following message is logged: **Hardware Status — [Hardware Status] QKVM has been automatically disabled by the operating system to free up system memory.**

Others with the same experience? How to prevent disabling Virtualization and Container Stations since my entire infrastructure runs on it?

---

<div class="post-metadata">

**Author:** ![HanzSung](https://community.qnap.com/user_avatar/community.qnap.com/hanzsung/32/168_2.png) [@HanzSung](https://community.qnap.com/u/HanzSung)\
**Post date:** [September 24, 2025, 9:34am UTC](https://community.qnap.com/t/apps-disabled-to-free-up-system-memory/2419/2 "2025-09-24T09:34:59Z")

</div>

I feel it might be similiar to this:

> [@Hybrid Mount File Cloud Gateway Troubles](https://community.qnap.com/t/hybrid-mount-file-cloud-gateway-troubles/2411):
>
> Hey all, I’m trying to set up a File Cloud Gateway in Hybrid Mount for my website. The website has something like 86,257 files but is less than 30GB. Hybrid Mount has been cranking away on this for the last couple of days and it seems to be nowhere near where it should be. I am seeing only about 1.8GB of used space. When running my load average is huge - right now it’s at 16 but I’ve seen it in the 30s. Also, now my memory (64 Gig) is filling up and QuTS Hero is shutting down Hybrid Sync t…

And it might need some attention on the QuTS hero behavior. Did you try to change the ARC usage to 40%?

---

<div class="post-metadata">

**Author:** ![amnesia](https://avatars.discourse-cdn.com/v4/letter/a/53a042/32.png) [@amnesia](https://community.qnap.com/u/amnesia)\
**Post date:** [September 24, 2025, 9:54am UTC](https://community.qnap.com/t/apps-disabled-to-free-up-system-memory/2419/3 "2025-09-24T09:54:40Z")

</div>

Perfect, thanks. I’ve adjusted it now down to 40%. Hope it helps. Do you know of any changes in the last firmware that would induce this behavior?

---

<div class="post-metadata">

**Author:** ![NA9D](https://community.qnap.com/user_avatar/community.qnap.com/na9d/32/1278_2.png) [@NA9D](https://community.qnap.com/u/NA9D)\
**Post date:** [September 24, 2025, 11:49am UTC](https://community.qnap.com/t/apps-disabled-to-free-up-system-memory/2419/4 "2025-09-24T11:49:01Z")

</div>

Yep. Sounds just like my issue. I was using more like 75% of memory but it seems like it’s being a little too aggressive…

---

<div class="post-metadata">

**Author:** ![amnesia](https://avatars.discourse-cdn.com/v4/letter/a/53a042/32.png) [@amnesia](https://community.qnap.com/u/amnesia)\
**Post date:** [September 24, 2025, 2:40pm UTC](https://community.qnap.com/t/apps-disabled-to-free-up-system-memory/2419/5 "2025-09-24T14:40:45Z")

</div>

It looks great so far. I’m not sure why it suddenly appeared after the very last firmware update, rather than in the last six months since I purchased the NAS. 🙂
