# Creating RAID-1 from TR Unit using 2 Drive only

**URL:** <https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808>\
**Category:** Storage\
**Created:** [March 20, 2025, 12:45pm UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808 "2025-03-20T12:45:42Z")\
**Posts on this page:** 10\
**Page:** 1

<div class="post-metadata">

**Author:** ![InfoSecOps](https://community.qnap.com/user_avatar/community.qnap.com/infosecops/32/1195_2.png) [@InfoSecOps](https://community.qnap.com/u/InfoSecOps)\
**Post date:** [March 20, 2025, 12:45pm UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/1 "2025-03-20T12:45:42Z")

</div>

Using the TR-004 and the Software RAID mode with the QNAP External RAID manager software on Windows.

What are the steps and the procedure to safely create RAID-1 using the Disk #3 and #4 only while retaining the data in the Disk #1 and #2 ?

---

<div class="post-metadata">

**Author:** ![Becker2020](https://avatars.discourse-cdn.com/v4/letter/b/ea5d25/32.png) [@Becker2020](https://community.qnap.com/u/Becker2020)\
**Post date:** [March 20, 2025, 12:50pm UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/2 "2025-03-20T12:50:43Z")

</div>

I think that doesn`t work.

You can’t change the raids.

---

<div class="post-metadata">

**Author:** ![InfoSecOps](https://community.qnap.com/user_avatar/community.qnap.com/infosecops/32/1195_2.png) [@InfoSecOps](https://community.qnap.com/u/InfoSecOps)\
**Post date:** [March 20, 2025, 12:53pm UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/3 "2025-03-20T12:53:37Z")

</div>

Ok, so how can I use just the two drives only while leaving the other two as Independent disks ?

---

<div class="post-metadata">

**Author:** ![Becker2020](https://avatars.discourse-cdn.com/v4/letter/b/ea5d25/32.png) [@Becker2020](https://community.qnap.com/u/Becker2020)\
**Post date:** [March 20, 2025, 5:45pm UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/4 "2025-03-20T17:45:37Z")

</div>

I think you must begann new with the TR-004

From user guide “The RAID enclosure does not support capacity expansion or RAID-level migration.”  
[user guide Tr-004](https://eu1.qnap.com/TechnicalDocument/Storage/Expansion%20Unit/TR%20Series/tr-00x-ug-en-us.pdf)

---

<div class="post-metadata">

**Author:** ![Guillaume](https://avatars.discourse-cdn.com/v4/letter/g/c67d28/32.png) [@Guillaume](https://community.qnap.com/u/Guillaume)\
**Post date:** [March 20, 2025, 9:35pm UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/5 "2025-03-20T21:35:34Z")

</div>

It’s not possible to have RAID1 on two disks, and the other two disks independent.

---

<div class="post-metadata">

**Author:** ![InfoSecOps](https://community.qnap.com/user_avatar/community.qnap.com/infosecops/32/1195_2.png) [@InfoSecOps](https://community.qnap.com/u/InfoSecOps)\
**Post date:** [March 22, 2025, 11:45am UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/6 "2025-03-22T11:45:11Z")

</div>

Thank you @Becker2020 and @Guillaume for the confirmation.  
I was under the impression that was possible as I used to managed TVS-XXX units.

---

<div class="post-metadata">

**Author:** ![Guillaume](https://avatars.discourse-cdn.com/v4/letter/g/c67d28/32.png) [@Guillaume](https://community.qnap.com/u/Guillaume)\
**Post date:** [March 24, 2025, 8:38am UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/7 "2025-03-24T08:38:13Z")

</div>

> [@InfoSecOps](#):
>
> Ok, so how can I use just the two drives only while leaving the other two as Independent disks ?

You can have 2 x RAID1 ( Example Disk 1 and 2 = RAID1 n°1 , and disk 3 and 4 = RAID1 n°2 )

But you can’t have disk 1 = single, disk 2 = single and disk 3 and 4 = RAID1.

For this kind of configuration, you need a TL- ( Ex TL-D800C ) connected to a NAS or managed directly by Windows.

In the case of a TL-, the disks are managed by the host and not by the unit.

---

<div class="post-metadata">

**Author:** ![InfoSecOps](https://community.qnap.com/user_avatar/community.qnap.com/infosecops/32/1195_2.png) [@InfoSecOps](https://community.qnap.com/u/InfoSecOps)\
**Post date:** [March 24, 2025, 11:22am UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/8 "2025-03-24T11:22:33Z")

</div>

@Guillaume ,  
The TR Unit has the Software mode function dipswitch mode, would that be possible to configure on the Windows 11 OS or it must be a Windows Server?

---

<div class="post-metadata">

**Author:** ![Guillaume](https://avatars.discourse-cdn.com/v4/letter/g/c67d28/32.png) [@Guillaume](https://community.qnap.com/u/Guillaume)\
**Post date:** [March 24, 2025, 11:58am UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/9 "2025-03-24T11:58:08Z")

</div>

You can set the TR-004 to “Single” and manage disks via the host

---

<div class="post-metadata">

**Author:** ![InfoSecOps](https://community.qnap.com/user_avatar/community.qnap.com/infosecops/32/1195_2.png) [@InfoSecOps](https://community.qnap.com/u/InfoSecOps)\
**Post date:** [March 24, 2025, 1:30pm UTC](https://community.qnap.com/t/creating-raid-1-from-tr-unit-using-2-drive-only/808/10 "2025-03-24T13:30:11Z")

</div>

That’s great, thank you so much @Guillaume for the sharing and explanation.
