# Tips for troubleshooting TS-130 restarting daily

**URL:** <https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060>\
**Category:** General\
**Created:** [April 20, 2025, 12:55pm UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060 "2025-04-20T12:55:33Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![Mike\_L](https://avatars.discourse-cdn.com/v4/letter/m/9de0a6/32.png) [@Mike\_L](https://community.qnap.com/u/Mike_L)\
**Post date:** [April 20, 2025, 12:55pm UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060/1 "2025-04-20T12:55:33Z")

</div>

For months my \<2 year old TS-130 NAS has been restarting most days, sometimes multiple times per day. Power is from a UPC and nothing else on it is restarting. The NAS fan is set for performance, and it works. No external drives, a 6TB WD inside. The restart times seem random, and not correlating to anything in the crontab. Nothing in the logs helps. Only storage.log seems to know there was a bad shutdown. Firmware is up to date.

My plan for troubleshooting is:

1. Run it with no hard drive installed, see if it still crashes over a week or so.
2. If not crashing, try another hard drive.
3. If still crashing, factory reset and keep running with no hard drive.

Any other suggestions? The KB only has 2 articles for TS-130, both for recovering one that won’t start up. I don’t know what other keywords to search for, “restart” shows up everywhere and “crash” gives nothing relevant.

---

<div class="post-metadata">

**Author:** ![dolbyman](https://community.qnap.com/user_avatar/community.qnap.com/dolbyman/32/136_2.png) [@dolbyman](https://community.qnap.com/u/dolbyman)\
**Post date:** [April 20, 2025, 1:58pm UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060/2 "2025-04-20T13:58:39Z")

</div>

Well running with no HDD is not really running much

If you swapped the HDD already and it still crashes, it could be busted RAM

---

<div class="post-metadata">

**Author:** ![Mike\_L](https://avatars.discourse-cdn.com/v4/letter/m/9de0a6/32.png) [@Mike\_L](https://community.qnap.com/u/Mike_L)\
**Post date:** [April 20, 2025, 3:18pm UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060/3 "2025-04-20T15:18:11Z")

</div>

Obviously the NAS is not very useful without a drive init, but the idea is to rule out the drive drawing too much power or something like that. I haven’t checked the compatibility list.

Anyway, I think some people are well along diagnosing this in another thread:

> [@Added new drive now TS230 randomly rebooting and resyncing for 48hrs](https://community.qnap.com/t/added-new-drive-now-ts230-randomly-rebooting-and-resyncing-for-48hrs/895):
>
> Hi all. I have a QNAP TS230 which had been fitted with a single WD 180EDFZ drive for a couple of years. In September, I added a Seagate 18TB EXOS drive and setup RAID1. That second drive worked fine but then failed recently and was replaced under warranty. This new drive is a Seagate 18TB EXOS X20. Full model number is ST18000NM003D. This model is not specifically mentioned in the compatibility list, but other EXOS 18TB drives are. The NAS is used solely for providing network access to my store…

---

<div class="post-metadata">

**Author:** ![Franklin](https://avatars.discourse-cdn.com/v4/letter/f/3e96dc/32.png) [@Franklin](https://community.qnap.com/u/Franklin)\
**Post date:** [April 29, 2025, 12:56am UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060/4 "2025-04-29T00:56:15Z")

</div>

What ram do you have?

---

<div class="post-metadata">

**Author:** ![Mike\_L](https://avatars.discourse-cdn.com/v4/letter/m/9de0a6/32.png) [@Mike\_L](https://community.qnap.com/u/Mike_L)\
**Post date:** [April 29, 2025, 1:14am UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060/5 "2025-04-29T01:14:41Z")

</div>

1 GB RAM, never close to full as far as I can tell. The latest update is that there was a firmware update 6 days ago, and it has not rebooted since. But it isn’t really doing anything; no backups happening, no external drives attached. Eventually I’ll get something going.

---

<div class="post-metadata">

**Author:** ![Franklin](https://avatars.discourse-cdn.com/v4/letter/f/3e96dc/32.png) [@Franklin](https://community.qnap.com/u/Franklin)\
**Post date:** [April 29, 2025, 11:33pm UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060/6 "2025-04-29T23:33:59Z")

</div>

What firmware? IIRC there was aproblem with NAS’s with a “30” in the name rebooting on the firmware that ended in.3079.

---

<div class="post-metadata">

**Author:** ![Mike\_L](https://avatars.discourse-cdn.com/v4/letter/m/9de0a6/32.png) [@Mike\_L](https://community.qnap.com/u/Mike_L)\
**Post date:** [April 30, 2025, 3:21am UTC](https://community.qnap.com/t/tips-for-troubleshooting-ts-130-restarting-daily/1060/7 "2025-04-30T03:21:33Z")

</div>

It’s QTS 5.2.4.3092 now, and yes it was 3079 before that. I think it also was rebooting with 3070 and 3006 before that.
