# TS-262 Memory Upgrade

**URL:** <https://community.qnap.com/t/ts-262-memory-upgrade/7017>\
**Category:** Compatibility\
**Created:** [September 22, 2026, 10:46pm UTC](https://community.qnap.com/t/ts-262-memory-upgrade/7017 "2026-09-22T22:46:04Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Stimple](https://avatars.discourse-cdn.com/v4/letter/s/f17d59/32.png) [@Stimple](https://community.qnap.com/u/Stimple)\
**Post date:** [September 22, 2026, 10:46pm UTC](https://community.qnap.com/t/ts-262-memory-upgrade/7017/1 "2026-09-22T22:46:04Z")

</div>

MacOS: ventura 13.7.8

TS-262

Serial Number QW5LU11906T

Firmware Version: 5.2.9 BUILD 20260514

Network Setup: Single port ( I’m assuming - I know no different)

Single Seagate 4 TB drive

I read where certain newer models of the TS-262 one could add more memory. I have 4 gig and would like to upgrade to 8 or 16 if possible?

How can I determine if my NAS can be updated with new memory. If It can, any recommendations on specific parameters? I read that DDR4-2666 up to 3200 SODIMMS were the spec?

---

<div class="post-metadata">

**Author:** ![dolbyman](https://community.qnap.com/user_avatar/community.qnap.com/dolbyman/32/136_2.png) [@dolbyman](https://community.qnap.com/u/dolbyman)\
**Post date:** [September 22, 2026, 10:56pm UTC](https://community.qnap.com/t/ts-262-memory-upgrade/7017/2 "2026-09-22T22:56:21Z")

</div>

Open up your NAS and see if your RAM is soldered or socketed.

There should be a few discussions about what RAM models would be compatible(google), to be on the safe side, you can always buy the RAM at a place with a good return policy (and make sure to keep the old RAM)

---

<div class="post-metadata">

**Author:** ![Stimple](https://avatars.discourse-cdn.com/v4/letter/s/f17d59/32.png) [@Stimple](https://community.qnap.com/u/Stimple)\
**Post date:** [September 23, 2026, 3:09pm UTC](https://community.qnap.com/t/ts-262-memory-upgrade/7017/3 "2026-09-23T15:09:17Z")

</div>

@dolbyman, thanks for quick reply. Yeah, I opened covering and I don’t see any soldering. I see i think some clips on side i’ll figure out how to pop open. Here is a picture. I did google and that is where i found the recommended memory being DDR4 either 2666 or 3200 mhz…

 ![IMG_4895](https://cdn-community.qnap.com/original/2X/8/8f06992789dd86055a2d403ef47a755cf8c0890c.jpeg)

---

<div class="post-metadata">

**Author:** ![dolbyman](https://community.qnap.com/user_avatar/community.qnap.com/dolbyman/32/136_2.png) [@dolbyman](https://community.qnap.com/u/dolbyman)\
**Post date:** [September 23, 2026, 3:21pm UTC](https://community.qnap.com/t/ts-262-memory-upgrade/7017/4 "2026-09-23T15:21:35Z")

</div>

I meant specific memory modules (that can be very tricky)

https://embed.reddit.com/r/qnap/comments/1lvgdh7/ts262_ram_upgrade_3200mhz_cl22/?embed=true&ref_source=embed&ref=share

---

<div class="post-metadata">

**Author:** ![Becker2020](https://avatars.discourse-cdn.com/v4/letter/b/ea5d25/32.png) [@Becker2020](https://community.qnap.com/u/Becker2020)\
**Post date:** [September 23, 2026, 3:43pm UTC](https://community.qnap.com/t/ts-262-memory-upgrade/7017/5 "2026-09-23T15:43:05Z")

</div>

> [@Stimple](#):
>
> DDR4 either 2666 or 3200 mhz

Hello,

i think you can use both  
For my TS-264 i use this

> [@Ts-264 specifications](https://community.qnap.com/t/ts-264-specifications/6338/4):
>
> Hello, my TS-264 work fine with 40 GB RAM and 2 NMVE-SSD (WD SN700).
