TS-469Pro, RAID 5 zeigt beim Start als inaktiv, Wiederherstellung behebt es, aber nach Neustart des NAS wieder inaktiv

Hallo,

ich habe einen erfolgreichen Festplattenaustausch „Disk by Disk“ für ein bestehendes RAID 5-Array durchgeführt, bei dem eine Festplatte ausgefallen war. Alle Daten sind vorhanden und das Array wurde von 4 x 3TB auf 4 x 4TB erweitert.

Allerdings erhalte ich nach einem Neustart des NAS eine Fehlermeldung und das RAID wird beim Neustart als „inaktiv“ angezeigt.

Ich kann das Problem beheben, indem ich im Storage Manager → Speicherplatz → Wiederherstellen gehe. Sobald der Vorgang abgeschlossen ist, funktioniert alles wieder einwandfrei.

Wenn ich MD_checker VOR dem Wiederherstellen ausführe, erhalte ich folgendes Ergebnis:

Welcome to MD superblock checker (v1.4) - have a nice day~

Scanning system...

HAL firmware detected!
Scanning Enclosure 0...

RAID metadata found!
UUID:           91ce1ae6:f7ad1daf:7518b59e:584eca62
Level:          raid5
Devices:        4
Name:           md1
Chunk Size:     64K
md Version:     1.0
Creation Time:  Apr 8 11:33:23 2025
Status:         OFFLINE
===============================================================================
 Disk | Device | # | Status |   Last Update Time   | Events | Array State
===============================================================================
   1  /dev/sda3  0   Active   Apr 21 08:43:42 2025   147422   AAAA
   2  /dev/sdb3  1   Active   Apr 21 08:43:42 2025   147422   AAAA
   3  /dev/sdc3  2   Active   Apr 21 08:43:42 2025   147422   AAAA
   4  /dev/sdd3  3   Active   Apr 21 08:43:42 2025   147422   AAAA
===============================================================================

Es scheint also beim Booten etwas nicht zu stimmen. Hat jemand eine Idee, wo ich mit der Fehlersuche beginnen sollte?

*********************
** QNAP NAS Report **
*********************

NAS Model:      TS-469 Pro
Firmware:       4.3.4 Build 20240618
System Name:    Skynet
Workgroup:      NAS
Base Directory: /share/CACHEDEV1_DATA
NAS IP address: 192.168.0.250

Default Gateway Device: bond0

          inet addr:192.168.0.250  Bcast:192.168.255.255  Mask:255.255.0.0
          inet6 addr: fe80::208:9bff:fed2:29d/64 Scope:Link
          UP BROADCAST RUNNING MASTER MULTICAST  MTU:4074  Metric:1
          RX packets:45164 errors:0 dropped:0 overruns:0 frame:0
          TX packets:77521 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:14710779 (14.0 MiB)  TX bytes:34653361 (33.0 MiB)


DNS Nameserver(s):192.168.0.1
192.168.0.1


HDD Information:

HDD1 - Model=WDC WD40EFPX-68C6CN0                    , FwRev=81.00A81, SerialNo=     WD-WX12DC4HAXF6

Model: WDC WD40EFPX-68C6CN0 (scsi)
Disk /dev/sda: 4001GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:

Number  Start   End     Size    File system     Name     Flags
 1      20.5kB  543MB   543MB   ext3            primary
 2      543MB   1086MB  543MB   linux-swap(v1)  primary
 3      1086MB  3992GB  3991GB                  primary
 4      3992GB  3992GB  543MB   ext3            primary
 5      3992GB  4001GB  8554MB  linux-swap(v1)  primary


001 Raw_Read_Error_Rate          0        200 200 051 OK
003 Spin_Up_Time                 0        100 253 021 OK
004 Start_Stop_Count             4        100 100 000 OK
005 Reallocated_Sector_Ct        0        200 200 140 OK
007 Seek_Error_Rate              0        200 200 000 OK
009 Power_On_Hours               208      100 100 000 OK
010 Spin_Retry_Count             0        100 253 000 OK
011 Calibration_Retry_Count      0        100 253 000 OK
012 Power_Cycle_Count            3        100 100 000 OK
192 Power-Off_Retract_Count      1        200 200 000 OK
193 Load_Cycle_Count             2        200 200 000 OK
194 Temperature_Celsius          37       110 108 000 OK
196 Reallocated_Event_Count      0        200 200 000 OK
197 Current_Pending_Sector       0        200 200 000 OK
198 Offline_Uncorrectable        0        100 253 000 OK
199 UDMA_CRC_Error_Count         0        200 200 000 OK
200 Multi_Zone_Error_Rate        0        100 253 000 OK

HDD2 - Model=WDC WD40EFPX-68C6CN0                    , FwRev=81.00A81, SerialNo=     WD-WX12DC4HAZAA

Model: WDC WD40EFPX-68C6CN0 (scsi)
Disk /dev/sdb: 4001GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:

Number  Start   End     Size    File system     Name     Flags
 1      20.5kB  543MB   543MB   ext3            primary
 2      543MB   1086MB  543MB   linux-swap(v1)  primary
 3      1086MB  3992GB  3991GB                  primary
 4      3992GB  3992GB  543MB   ext3            primary
 5      3992GB  4001GB  8554MB  linux-swap(v1)  primary


001 Raw_Read_Error_Rate          0        200 200 051 OK
003 Spin_Up_Time                 0        100 253 021 OK
004 Start_Stop_Count             3        100 100 000 OK
005 Reallocated_Sector_Ct        0        200 200 140 OK
007 Seek_Error_Rate              0        200 200 000 OK
009 Power_On_Hours               182      100 100 000 OK
010 Spin_Retry_Count             0        100 253 000 OK
011 Calibration_Retry_Count      0        100 253 000 OK
012 Power_Cycle_Count            2        100 100 000 OK
192 Power-Off_Retract_Count      0        200 200 000 OK
193 Load_Cycle_Count             2        200 200 000 OK
194 Temperature_Celsius          35       112 111 000 OK
196 Reallocated_Event_Count      0        200 200 000 OK
197 Current_Pending_Sector       0        200 200 000 OK
198 Offline_Uncorrectable        0        100 253 000 OK
199 UDMA_CRC_Error_Count         0        200 200 000 OK
200 Multi_Zone_Error_Rate        0        100 253 000 OK

HDD3 - Model=WDC WD40EFPX-68C6CN0                    , FwRev=81.00A81, SerialNo=     WD-WX12DC4HA12K

Model: WDC WD40EFPX-68C6CN0 (scsi)
Disk /dev/sdc: 4001GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:

Number  Start   End     Size    File system     Name     Flags
 1      20.5kB  543MB   543MB   ext3            primary
 2      543MB   1086MB  543MB   linux-swap(v1)  primary
 3      1086MB  3992GB  3991GB                  primary
 4      3992GB  3992GB  543MB   ext3            primary
 5      3992GB  4001GB  8554MB  linux-swap(v1)  primary


001 Raw_Read_Error_Rate          0        200 200 051 OK
003 Spin_Up_Time                 0        100 253 021 OK
004 Start_Stop_Count             3        100 100 000 OK
005 Reallocated_Sector_Ct        0        200 200 140 OK
007 Seek_Error_Rate              0        200 200 000 OK
009 Power_On_Hours               195      100 100 000 OK
010 Spin_Retry_Count             0        100 253 000 OK
011 Calibration_Retry_Count      0        100 253 000 OK
012 Power_Cycle_Count            2        100 100 000 OK
192 Power-Off_Retract_Count      0        200 200 000 OK
193 Load_Cycle_Count             2        200 200 000 OK
194 Temperature_Celsius          35       112 110 000 OK
196 Reallocated_Event_Count      0        200 200 000 OK
197 Current_Pending_Sector       0        200 200 000 OK
198 Offline_Uncorrectable        0        100 253 000 OK
199 UDMA_CRC_Error_Count         0        200 200 000 OK
200 Multi_Zone_Error_Rate        0        100 253 000 OK

HDD4 - Model=WDC WD40EFPX-68C6CN0                    , FwRev=81.00A81, SerialNo=     WD-WX12DC4HAJ6Z

Model: WDC WD40EFPX-68C6CN0 (scsi)
Disk /dev/sdd: 4001GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:

Number  Start   End     Size    File system     Name     Flags
 1      20.5kB  543MB   543MB   ext3            primary
 2      543MB   1086MB  543MB   linux-swap(v1)  primary
 3      1086MB  3992GB  3991GB                  primary
 4      3992GB  3992GB  543MB   ext3            primary
 5      3992GB  4001GB  8554MB  linux-swap(v1)  primary


001 Raw_Read_Error_Rate          0        200 200 051 OK
003 Spin_Up_Time                 0        100 253 021 OK
004 Start_Stop_Count             3        100 100 000 OK
005 Reallocated_Sector_Ct        0        200 200 140 OK
007 Seek_Error_Rate              0        200 200 000 OK
009 Power_On_Hours               239      100 100 000 OK
010 Spin_Retry_Count             0        100 253 000 OK
011 Calibration_Retry_Count      0        100 253 000 OK
012 Power_Cycle_Count            2        100 100 000 OK
192 Power-Off_Retract_Count      0        200 200 000 OK
193 Load_Cycle_Count             2        200 200 000 OK
194 Temperature_Celsius          36       111 109 000 OK
196 Reallocated_Event_Count      0        200 200 000 OK
197 Current_Pending_Sector       0        200 200 000 OK
198 Offline_Uncorrectable        0        100 253 000 OK
199 UDMA_CRC_Error_Count         0        200 200 000 OK
200 Multi_Zone_Error_Rate        0        100 253 000 OK

Volume Status

/dev/md1:
        Version : 1.0
  Creation Time : Tue Apr  8 11:33:23 2025
     Raid Level : raid5
     Array Size : 11691190848 (11149.59 GiB 11971.78 GB)
  Used Dev Size : 3897063616 (3716.53 GiB 3990.59 GB)
   Raid Devices : 4
  Total Devices : 4
    Persistence : Superblock is persistent

  Intent Bitmap : Internal

    Update Time : Mon Apr 21 10:31:42 2025
          State : active
 Active Devices : 4
Working Devices : 4
 Failed Devices : 0
  Spare Devices : 0

         Layout : left-symmetric
     Chunk Size : 64K

           Name : 1
           UUID : 91ce1ae6:f7ad1daf:7518b59e:584eca62
         Events : 147422

    Number   Major   Minor   RaidDevice State
       5       8        3        0      active sync   /dev/sda3
       7       8       19        1      active sync   /dev/sdb3
       6       8       35        2      active sync   /dev/sdc3
       4       8       51        3      active sync   /dev/sdd3

Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath]
md1 : active raid5 sda3[5] sdd3[4] sdc3[6] sdb3[7]
                 11691190848 blocks super 1.0 level 5, 64k chunk, algorithm 2 [4/4] [UUUU]
                 bitmap: 0/30 pages [0KB], 65536KB chunk

md322 : active raid1 sdd5[3](S) sdc5[2](S) sdb5[1] sda5[0]
                 7235136 blocks super 1.0 [2/2] [UU]
                 bitmap: 0/1 pages [0KB], 65536KB chunk

md256 : active raid1 sdd2[3](S) sdc2[2](S) sdb2[1] sda2[0]
                 530112 blocks super 1.0 [2/2] [UU]
                 bitmap: 0/1 pages [0KB], 65536KB chunk

md13 : active raid1 sda4[33] sdc4[34] sdd4[32] sdb4[35]
                 458880 blocks super 1.0 [32/4] [UUUU____________________________]
                 bitmap: 1/1 pages [4KB], 65536KB chunk

md9 : active raid1 sda1[33] sdc1[34] sdd1[32] sdb1[35]
                 530048 blocks super 1.0 [32/4] [UUUU____________________________]
                 bitmap: 1/1 pages [4KB], 65536KB chunk

unused devices: <none>

Disk Space:

Filesystem                Size      Used Available Use% Mounted on
none                    200.0M    183.5M     16.5M  92% /
devtmpfs                  1.5G      8.0K      1.5G   0% /dev
tmpfs                    64.0M    268.0K     63.7M   0% /tmp
tmpfs                     1.5G         0      1.5G   0% /dev/shm
tmpfs                    16.0M         0     16.0M   0% /share
/dev/md9                509.5M    156.4M    353.1M  31% /mnt/HDA_ROOT
cgroup_root               1.5G         0      1.5G   0% /sys/fs/cgroup
/dev/sdf1               509.5M    156.9M    352.6M  31% /share/external/DEV3306_1
tmpfs                    16.0M         0     16.0M   0% /share/NFSv=4
/dev/sdf4               371.0M    347.7M     23.3M  94% /share/external/DEV3306_4
/dev/sdg1               509.5M    156.9M    352.6M  31% /share/external/DEV3308_1
/dev/sdg4               371.0M    347.9M     23.1M  94% /share/external/DEV3308_4
/dev/md13               371.0M    345.1M     25.9M  93% /mnt/ext
/dev/ram2               433.9M      2.3M    431.6M   1% /mnt/update
tmpfs                    64.0M      2.5M     61.5M   4% /samba
tmpfs                    16.0M     48.0K     16.0M   0% /samba/.samba/lock/msg.lock
tmpfs                    16.0M         0     16.0M   0% /mnt/ext/opt/samba/private/msg.sock
tmpfs                     1.0M         0      1.0M   0% /mnt/rf/nd
/dev/mapper/cachedev1
                         10.6T      7.7T      2.9T  73% /share/CACHEDEV1_DATA

Mount Status:

none on /new_root type tmpfs (rw,mode=0755,size=204800k)
/proc on /proc type proc (rw)
devpts on /dev/pts type devpts (rw)
sysfs on /sys type sysfs (rw)
tmpfs on /tmp type tmpfs (rw,size=64M)
tmpfs on /dev/shm type tmpfs (rw)
tmpfs on /share type tmpfs (rw,size=16M)
none on /proc/bus/usb type usbfs (rw)
/dev/md9 on /mnt/HDA_ROOT type ext3 (rw,data=ordered)
cgroup_root on /sys/fs/cgroup type tmpfs (rw)
/dev/sdf1 on /share/external/DEV3306_1 type ext3 (rw)
tmpfs on /share/NFSv=4 type tmpfs (rw,size=16M)
/dev/sdf4 on /share/external/DEV3306_4 type ext3 (rw)
/dev/sdg1 on /share/external/DEV3308_1 type ext3 (rw)
/dev/sdg4 on /share/external/DEV3308_4 type ext3 (rw)
cpu on /sys/fs/cgroup/cpu type cgroup (rw,cpu)
/dev/md13 on /mnt/ext type ext4 (rw,data=ordered,barrier=1,nodelalloc)
none on /sys/kernel/config type configfs (rw)
/dev/ram2 on /mnt/update type ext2 (rw)
tmpfs on /samba type tmpfs (rw,size=64M)
tmpfs on /samba/.samba/lock/msg.lock type tmpfs (rw,size=16M)
tmpfs on /mnt/ext/opt/samba/private/msg.sock type tmpfs (rw,size=16M)
tmpfs on /mnt/rf/nd type tmpfs (rw,size=1m)
nfsd on /proc/fs/nfsd type nfsd (rw)
rpc_pipefs on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw)
/dev/mapper/cachedev1 on /share/CACHEDEV1_DATA type ext4 (rw,usrjquota=aquota.user,jqfmt=vfsv0,user_xattr,data=ordered,data_err=abort,delalloc,nopriv,nodiscard,acl)


Memory Information:

             total       used       free     shared    buffers     cached
Mem:       3072244    1926688    1145556          0     710848     733380
Swap:     24542452          0   24542452

NASReport completed on 2025-04-21 10:33:48 (/tmp/nasreport)

Habe einen RAID-Scrub durchgeführt, der keine Fehler ergab, neu gestartet, aber das gleiche Problem. Es wird als inaktiv angezeigt und ich muss es manuell wiederherstellen, damit es zurückkommt.
Hat jemand eine Idee, wie man das beheben kann? Es ist, als ob eine Boot-Konfigurationsdatei aktualisiert werden müsste, aber ich weiß nicht, wo ich anfangen oder sie finden soll.
Jede Hilfe wird geschätzt.

Gibt es eine Konfigurationsdatei, die eingesehen werden kann, um zu überprüfen, was beim Booten passiert?

Irgendwelche Ideen zu diesem Problem?

Eröffnen Sie ein Ticket. Falls QNAP nicht (bereit ist zu) helfen, könnte es die beste Option sein, das NAS komplett neu aufzusetzen.

Ich habe versucht, Qnap mit verschiedenen Browsern zu kontaktieren, aber wenn ich versuche, die Anfrage abzuschicken, bleibt die Seite einfach stehen und das Symbol dreht sich in der Mitte der Seite – ich kann sie nicht kontaktieren.

Habe dies ausgeführt und jetzt startet es problemlos
/etc/init.d/init_lvm.sh

Danke für das Update, du hast mein Wochenende gerettet. hehe